Announcement

Collapse
No announcement yet.

Block identification

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Block identification

    I found the block number on my engine, was wondering what they mean:

    E5AE
    03B
    Pebbles-1968 Ford F250
    Pile of Junk! An Electronics Project Site (To get wet by)<---Clicky! NEW STUFF!!!!

    #2
    E = 8 (decade)
    5 = 5 (year)

    So it's a 1985 block... not too often have I seen year models with blocks cast the same year.
    2011 Mustang GT Premium, MT82, Kona/Saddle, HIDs, 3.73s, 19s, hood/side stripes, UPR 1.5" springs with adjustable panhard bar, and UMI solid LCAs and relocation brackets.
    1992 Explorer Eddie Bauer, slight lift, 34s, and A/C...
    1979 Bronco Custom, 351M/C6/NP205, 4" lift, 35s, lots of fender trimming.

    Comment


      #3
      Dumb question here...I was ripping into my 302 roller block e7 casting but the rods were C8's...why would 1968 rods be in my 88 motor? Did ford just use the same rods through all the years?

      2009 Ford F-350 6.4 powerstroke diesel. 1977 Ford F-150 built 300 six, 5 speed trans. 1976 MG MGB roadster, 359w, t5 5 speed. 1996 Kawasaki ninja ZX6R.
      My rod is glowing, my bead is clean, my middle name is acetylene

      Comment


        #4
        Where is the block number?
        People should not be afraid of their governments. Governments should be afraid of their people.

        Comment


          #5
          Originally posted by darkknight
          Where is the block number?
          Behind the starter.
          http://secondhandracing.com/Home.aspx
          http://secondhandradio.com/

          R.I.P. Jason P Harrill 6-12-06

          http://www.grandmarq.net/vb/showthread.php?t=5634

          Comment


            #6
            Cool thanks man :->
            People should not be afraid of their governments. Governments should be afraid of their people.

            Comment


              #7
              1985 motors have a flat tappet cam, but they have the bosses in the lifter galley that can be drilled for the roller lifter retainer. Probably means its the original one in the car.

              No idea about the rods but I wouldn't be highly surprised if the original connecting rod design from 1968 (first year for the 302 I believe) is still in use. I didn't pay attention to the castings on my rods.
              86 Lincoln Town Car (Galactica).
              5.0 HO, CompCams XE258,Scorpion 1.72 roller rockers, 3.55 K code rear, tow package, BHPerformance ported E7 heads, Tmoss Explorer intake, 65mm throttle body, Hedman 1 5/8" headers, 2.5" dual exhaust, ASP underdrive pulley

              91 Lincoln Mark VII LSC grandpa spec white and cranberry

              1984 Lincoln Continental TurboDiesel - rolls coal

              Originally posted by phayzer5
              I drive a Lincoln. I can't be bothered to shift like the peasants and rabble rousers

              Everything looks like voodoo if you don't understand how it works

              Comment


                #8
                Darknight-If you lay down under the car, look between the starter and the block, it will be on the lip where the bellhousing for the trans mounts up
                Pebbles-1968 Ford F250
                Pile of Junk! An Electronics Project Site (To get wet by)<---Clicky! NEW STUFF!!!!

                Comment


                  #9
                  Originally posted by Mercmarquis
                  Dumb question here...I was ripping into my 302 roller block e7 casting but the rods were C8's...why would 1968 rods be in my 88 motor? Did ford just use the same rods through all the years?

                  Yes...... not an uncommon thing. Why reinvent the wheel? I believe that other rods were also used in that time frame though.

                  Comment

                  Working...
                  X