I tried it with the rubber FeltPro gaskets and gasket maker on both sides, but I have heard of professionals doing a single bead of thick RTV. What works best for you all?
 |
-
1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph. -
You are talking about the front and rear seals, correct? If so I heard a thick bead of rtv works great.
2009 Ford F-350 6.4 powerstroke diesel. 1977 Ford F-150 built 300 six, 5 speed trans. 1976 MG MGB roadster, 359w, t5 5 speed. 1996 Kawasaki ninja ZX6R.
My rod is glowing, my bead is clean, my middle name is acetylene -
yes yes front and rear seals, the sides are self explanitory
1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
Last time I put an intake on I did thick TRV on the front and back, and not a hint of a leak.
Comment
-
RTV all the way. no leaks on mine or the 302 we built. Edelbrock even recommends using just the RTVhttp://secondhandracing.com/Home.aspx
http://secondhandradio.com/
R.I.P. Jason P Harrill 6-12-06
http://www.grandmarq.net/vb/showthread.php?t=5634Comment
-
whatabout the timing cover to block gasket, and the timing cover to water pump? Where can you get a timing cover to block gasket?1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
mine came in the Fel-Pro full gasket kit. damn set even had new valve seals in it.along with a bunch of other gaskets i cant use. 351 throttle body gasket, egr gasket, upper-lower manifold gasket. (goddamn the ports on a factory 351 manifold are massive compared to a 302)http://secondhandracing.com/Home.aspx
http://secondhandradio.com/
R.I.P. Jason P Harrill 6-12-06
http://www.grandmarq.net/vb/showthread.php?t=5634Comment
Comment