what would you all use, a 1 piece rubber gasket or a 1 piece cork gasket for the oil pan, with RTV beads at the corners? What is your preference.
 |
-
1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph. -
fel-pro one piece rubber... all the way.
I dont think you need any sealer in the corners, install it dry and make sure you torque it properly.2003 Town Car Signature - 3.27 RAR, Dual exhaust and J-mod - SOLD 9/2011
89 Crown Victoria LX HPP -- SOLD 9/2010
88 Grand Marquis LS - The Original -- Totaled 5/2006
I rebuild AOD/AODE/4R70W/4R75E transmissions....Check out my Facebook page: https://www.facebook.com/pages/North...48414635312478 -
felpro permadry all the way
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
No problems with cork over here.Comment
-
What about on a Dodge 3.0L V6?1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
One piece if at all possible. In the car, no way in hell I'd put a 4 piece cork in, simply because its a lot more work. I have installed 4 piece cork gaskets with the motor on the stand and not had leakage, but under the car, forget it.86 Lincoln Town Car (Galactica).
5.0 HO, CompCams XE258,Scorpion 1.72 roller rockers, 3.55 K code rear, tow package, BHPerformance ported E7 heads, Tmoss Explorer intake, 65mm throttle body, Hedman 1 5/8" headers, 2.5" dual exhaust, ASP underdrive pulley
91 Lincoln Mark VII LSC grandpa spec white and cranberry
1984 Lincoln Continental TurboDiesel - rolls coal
Originally posted by phayzer5
I drive a Lincoln. I can't be bothered to shift like the peasants and rabble rousersComment
-
yeah, I think the key is clean surfaces, and an inch-lb torque wrench for the proper even torque.1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
no gasket required......they used rtv from the factory.......use permatex ultra black or ultra greyOriginally posted by 89LincolnTWNcar View Post
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
ORLY? Thats why the pan was sealed with grey RTV, I thought someone had re-did it.1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
The Dodge 3.0L is actually a Mitsubishi motor. FWIW.Originally posted by 89LincolnTWNcar View Post91 Mercury CP, Lopo 302, AOD, 3.08LSD. 3g upgrade, Moog wagon coils up front, cc819s in the back. KYB GR-2 police shocks. Energy suspension control arm bushings. Smog deleted.Originally posted by gadget73
93 F-150 XLT, 302, ZF 5-spd from 1-ton, 4wd.
Daily--07 Civic Coupe. Bone stock with 25k miles
Wife--14 Subaru Outback. 6-speed.
95 Subaru Legacy Wagon--red--STOLEN 1/6/13Comment
-
yes.....replace the oil pump and the water pump and the timing belt too while its apart......the 3.0 got a bad rep for burning oil, but they are an excellent engine.....i know how to fix the oil burning issues too if they come up
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
Damn rights on the oil and water pumps, timing belt as well. 3.0L is a good little engine but the valve guides are cr@p.1990 LTD Crown Vic w/ dead 5.0
1984 Pontiac 6000 cammed 2.5L Iron Duke
1986 F-150 300 6cyl 5spd.
1994 Crown Vic... Free, bad trans?Comment
-
Glad you guys know a bit about it, I'm replacing the oil and water pumps, I had to pull the engine cuz my uncle put 5 quarts of oil in it, when it had 3 in it, and it blew every seal in the motor including the head gaskets. I had the heads resurfaced, cleaned, the guides were fine, and new positive valve stem seals installed, and I am using brand new headbolts. Any tips for the rear main seal?1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
the guides werent dropped? excellent!
do not scratch the crank when changing the seal......to get the old one out, take a tiny flathead screwdriver and pry out on the seal using the block as leverage, be very carefull that you do not get anywhere near the crank with that screwdriver.......when you go to put the new seal in, pack the inside with grease so the spring in the seal cant pop out.....install the new seal carefully with a small hammer, make sure it is installed evenly
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
Yeah I was surprised the guides were OK. The heads might have been worked on before I don't know. The cars odo stopped at 68,000 a few years ago, so it might have around 90-100K now. Still pretty low milage.
Oh should I remove that rear main seal housing and install the seal? or just leave it be?1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
Comment