If I just stuck on my explorer intakes with the lo-po bored out EGR and 60mm tb, would that be a waste?
 |
-
1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph. -
It'll flow better than the stock HO....Don't know if it'd be worth it though.Builder/Owner of Badass Panther Wagons
Busy maintaining a fleet of Fords -
yea...it would almost be like a bottle neck effect I would think...sigpic
1989 Ford Crown Victoria
99KComment
-
you might gain a few ponies but the bottle neck would just move from the stock upper to the stock heads. plus you would probably loose torque due to the reduced velocity because of the larger runners. I would not do it unless you have the parts to accompany the intake. E7 heads at least...Comment
-
I've decided to sell the intakes, they are in the for sale section
1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
put it on
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
oooo put them on and later up grade to Mass air too and then later port the heads .....do you allready have HO? if not put that on the list too! Rock onComment
-
do I have HO!!??? Of course I do!
I WOULD be putting these on if I could find a Lightning EGR spacer, but they are impossible to locate. I've had 3 people pm me that they have one and never PM me back on Lightning forums.....1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
just modify a mustang spacer for christs sake
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
Ok I'll try that. Im guessing drilling and tapping, then inserting studs into the tapped holes will do it.1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
Fuck drilling and tapping, just use a regular Mustang spacer, any EFI Mark VII accelerator and cruise control cables, and a 3.8 EFI T-bird TV cable - works like a charm, especially if you take the extra effort of oiling the cables.Comment
-
hmmm, I've never changed TV cables before, or even looked at how they are attached down there, this will be a new venture for me.1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
One bolt actually attaches the cable jacket to a bracket at the trans, and it just pops off at the lever on the trans, pretty much just like the throttle cable. Very simple. The down side is the backwards cables look messy (in my opinion anyway)86 Lincoln Town Car (Galactica).
5.0 HO, CompCams XE258,Scorpion 1.72 roller rockers, 3.55 K code rear, tow package, BHPerformance ported E7 heads, Tmoss Explorer intake, 65mm throttle body, Hedman 1 5/8" headers, 2.5" dual exhaust, ASP underdrive pulley
91 Lincoln Mark VII LSC grandpa spec white and cranberry
1984 Lincoln Continental TurboDiesel - rolls coal
Originally posted by phayzer5
I drive a Lincoln. I can't be bothered to shift like the peasants and rabble rousersComment
Comment